fs-etfs-ram

Options:

Board Support Packages may include a board-specific embedded transaction filesystem. All fs-etfs-* filesystems use the same common options as fs-etfs-ram; for driver-specific options, see the BSP documentation or use the -D use option, as described in “Driver options,” below.

Common options

-a

Update access times (atime). Default is to not update atime, to reduce the number of flash writes.

-b priority

Run background reclaim at this priority. Default is 8.

-B

Don't detach and run in the background. This is useful for debugging.

-c nclusters

Set the cache size. The cache holds recently read clusters in RAM, reducing the need to access the device if the same cluster is read again. It's also used to combine small writes into larger writes consisting of multicluster transactions. This reduces file fragmentation across the device and improves filesystem startup time. Since most devices are very fast, a small cache is usually acceptable. Larger caches may be desirable if many files are being written with small writes concurrently. The default value is 64 clusters, where cluster size is usually 1 KB or 2 KB, depending on the device.

-C 0|1|2

Disable error checking/correction.

0: No CRC check, no ECC correction (RAM).
1: CRC check, no ECC correction (SRAM or NOR Flash).
2: CRC check, ECC correction (NAND Flash).

Default: use CRCs for error checking and ECCs for error correction.

-D

Specify driver options; see “Driver options,” below.

-e

Erase the device and create an empty filesystem that is ready to use. For NAND flash, factory-marked bad blocks are not erased. Blocks that become bad during normal use (worn-out blocks) are also skipped during the erasing.

-f numfiles

Set maximum number of files. The default value is 4096, with a maximum of 32,767.

-F num

Defragment if the average extent is less than num clusters. The value of num must be in the range from 0 through 16. Default is 6. The fs-etfs-ram utility doesn't defragment if num is 0.

-I

Perform internal integrity checks of internal data structures while the filesystem is running. This slows down the filesystem. Its main purpose is for debugging new drivers and new versions of the filesystem.

-m mountpoint

Set the directory for fs-etfs-ram to use as its mountpoint. On an embedded system where ETFS is the major filesystem, this is set as -m / for taking over the root. If you don't specify this option, the ETFS isn't mounted.

-o numattr

Set the number of attributes to cache, which speeds up opens slightly. Default is 8.

-r kbytes

Set the size of the raw partition /dev/etfs1, in kilobytes. This partition, if present, is typically used to hold a boot image made using the mkifs utility. The default size is 0.

-R

Reserve a percentage of the flash to avoid issues that arise when a flash device becomes completely full. Default is 5% (of the device size).

-S

Implement transaction checksum using a fast and simple sum calculation rather than the default polynomial CRC algorithm. This may be faster but less robust.

-s num

Set the number of flash blocks to use as spares. One spare block is required to perform a reclaim. During normal operation, flash devices wear, which causes flash blocks to fail. More than one spare block provides extra redundancy. Default is 4.

-t sec

Set a timer for background operations. Default is 5 seconds.

-v[v...]

Set verbosity. Each -v increases verbosity.

-W erasediff

Set wear-leveling span. Allow flash blocks to have erase counts that differ by more than erasediff before attempting to either :

force them into service if they are below erasediff
Or:
give them a rest if they are above erasediff.

The default value is 50.

-x nextents

Cache this number of file extent offsets. This option reduces the processing needed to read through file extents on the device. Default is 8.

Driver options

use

Get a list of driver-specific options. This option causes the filesystem to print a usage message and then terminate without accessing the device.

size=nnM

Set the size of the RAM disk to nn megabytes. The default is 16 MB.

Description:

The embedded transaction filesystem (ETFS) implements a high-reliability filesystem for use with embedded solid-state memory devices with particular attention to NAND flash memory. The filesystem supports a fully hierarchical directory structure with POSIX semantics as shown in the table below:

POSIX capability	Supported by ETFS
Access date	Yes (if enabled with -`a` command-line option)
Modification date	Yes
Status change date	Yes
Max filename length	91 characters
User permission	Yes
Group permissions	Yes
Other permissions	Yes
Directories	Yes
Hard links	No
Symbolic links	Yes

POSIX capability

Supported by ETFS

Access date

Yes (if enabled with -a command-line option)

Modification date

Yes

Status change date

Yes

Max filename length

91 characters

User permission

Yes

Group permissions

Yes

Other permissions

Yes

Directories

Yes

Hard links

Symbolic links

Yes

The raw partition is used for boot images and is always at the start of the device. It may be zero bytes long if no boot image is needed. The filesystem partition is mounted in the pathname space as specified by the -m option.

If you don't specify the -m option, the filesystem isn't mounted. You can use the mount command to mount it later:

mount -tetfs /dev/etfs2 my_mountpoint

ETFS is a filesystem composed entirely of transactions. Every write operation, whether of user data or filesystem metadata, consists of a transaction. A transaction either succeeds or is treated as if it never occurred.

Examples:

Start ETFS to implement a temporary filesystem in RAM mounted at /tmp. Since it's not persistent across a reboot, and since RAM is reliable, you should disable all data error detection and correction (-C 0). The -e option initializes an empty filesystem ready to go upon startup. Since the filesystem is in high-speed RAM, you should specify the smallest cache possible with the -c 0 option.

Caveats:

Although ETFS supports most POSIX semantics, some functionality isn't implemented in order to keep the driver simple and efficient. The unsupported POSIX semantics include:

`fs-etfs-ram`

Syntax:

Runs on: